Flyin Optronics Co.,Ltd

World's Leading Optical Devices Manufacturer

Current Position: >Optical Transceiver >100G Optical Transceiver >100Gb/s 10KM CFP2 Optical Transceiver
100Gb/s 10KM CFP2 Optical Transceiver595221d4573a9.jpg
100Gb/s 10KM CFP2 Optical Transceiver

Data Rate:

100Gbps

Distance:

10km

Connector:

LC

DDM:

Yes

No

Wavelength:

1296.56/1300.05/1304.58/1309.14

Reply Within 12 Hours

Description

Parameters

PDF

FeaturesApplications
Direct LC receptacle optical interfaceOTN-OTU4
Single +3.3V power supplySwitch to switch interface
Hot-pluggableSwitch to router interface
Operating optical data rate up to 112GbpsP to P Access Network
Operating electrical serial data rate up to 10.3125Gbps
10 parallel electrical serial interface
Transmission distance up to 10km
AC coupling of CML signalsStandards
1310 nm window cooled EA-DFB LDCompliant with IEEE 802.3ba
PIN ROSACompliant with CFP MSA hardware specification
Low power dissipation(Max:16W)Compliant with CFP MSA management specification
Built in digital diagnostic functionCompliant with ITU-T G.709/Y.1331
Operating case temperature range:0℃ to 70℃Compliant with RoHS & WEEE
Compliant with RoHS
MDIO Communication Interface


Package outline(Unit:mm)

5913b319051e2.png



The production workshop show

Ordering Information

Part NumberProduct Description
FYCP2-4LO4-10BDCFP2: 1310nm-LAN-Cooled-EMA DFB-LD, 103.125Gbps, 10km, 0ºC ~ +70ºC, Ethernet Version, DDM

Absolute Maximum Ratings

ParameterSymbolMinMax
Storage Temperature Range(℃)Ts-40+85
Relative Humidity(%)RH585
Power Supply Voltage(V)Vcc-0.5+3.6
Operating Case Temperature Range(℃)Tc-5+75
Receiver Damage Threshold Per Lane(dBm)Pdag+5.5-

Recommended Operating Conditions

ParameterSymbolMinTypMax
Operating Case Temperature Range(℃)Tc0
70
Power Supply Voltage(V)Vcc3.23.33.4
Data rate(Gb/s)

103.125112

Specifications (tested under recommended operating conditions, unless otherwise noted)

ParameterSymbolMinTypMaxNotes
Voltage Supply Electrical Characteristics
Supply Current(A)Tx SectionIcc--3.51
Rx Section
Power Supply NoiseVrip

2%DC-1MHz


3%1-10MHz
Dissipation(W)Class5Pw

12
Low Power Dissipation(W)Plow

2
Inrush Current(mA/usec)Class5I-inrush

200
Turn-off Current(mA/usec)I-turnoff-200


Different Signal Electrical Characteristics
Single Ended Data Input Swing(mV)
55-525
Single Ended Data Output Swing(mV)
150-500
Differential Signal Output Resistance(Ω)
80
120
Differential Signal Input Resistance(Ω)
80
120
3.3V LVCMOS Electrical Characteristics)
Input High Voltage(V)3.3VIH2.0-Vcc+0.3
Input Low Voltage(V)3.3VIH-0.3-0.8
Input Leakage Current(uA)3.3IIN-10-+10
Output High Voltage (IOH=100uA)(V)3.3VOHVcc-0.2--
Output Low Voltage (IOL=100uA)(V)3.3VOH
-0.2
Minimum Pulse Width of Control Pin Signal(us)t_CNTL100


1.2V LVCMOS Electrical Characteristics
Input High Voltage(V)1.2VIH0.84
1.5
Input Low Voltage(V)1.2VIL-0.3
0.36
Input Leakage Current(uA)1.2IIN-100
+100
Output High Voltage(V)1.2VOH1.0
1.5
Output High Current(mA)1.2IOH

-4
Output Low Current(mA)1.2IOL+4


Input Capacitance(pF)Ci+4
10
Optical transmitter Characteristics
Signaling Rate for Each Lane(100GbE)(Gbps)
-25.78125

Signaling Rate for Each Lane(OTU4)(Gbps)
-27.95249

Four Lane Wavelength Range(nm)λ11294.531295.561296.59
λ21299.021300.051301.09
λ31303.541304.581305.63
λ41308.091308.091310.19
Side Mode Suppression Ratio(dB)SMSR30
-
Total Average Launch Power(dBm)Pt-
10.5
Average Launch Power for Each Lane(100GbE)(dBm)Pa-4.3
+4.52
Average Launch Power for Each Lane(OTU4)(dBm)-2.9
+4.5
Optical Modulation Amplitude for Each Lane(dBm)OMA-1.3
4.53
Transmitter and Dispersion Penalty for Each Lanes(TDP)


2.2
Extinction Ratio (100GbE)(dB)EX4


Extinction Ratio (OTU4)(dB)7


RIN20OMA(dB/Hz)


-130
Optical Return Loss Tolerance(dB)


20
Transmitter Reflectance(dB)


-12
Eye DiagramCompliant with IEEE 802.3ba-LR4/OTU4
Optical receiver Characteristics
Signaling Rate for Each Lane(100GbE)(Gbps)
-25.78125

Signaling Rate for Each Lane(OTU4)(Gbps)
-27.95249

Four Lane Wavelength Range(nm)λ11294.531295.561296.59
λ21299.021300.051301.09
λ31303.541304.581305.63
λ41308.091308.091310.19
Overload Input Optical Power(dBm)Pmax5.5

5
Average Receive Power for Each Lane(100GE)(dBm)Pa-10.6
4.56&7
Average Receive Power for Each Lane(OTU4 with Tx ER of 4 to 6.5 dB)(dBm)Pa-6.9
4.0
Average Receive Power for Each Lane(OTU4 with Tx ER > 7 dB)
-8.8
2.9
Receive Power In OMA for Each Lane(dBm)PinOMA-
4.5
Difference in Receive Power between Any Two Lanes(dBm)
-
5.5
Receiver Sensitivity in OMA for Each Lane(100GbE) at BER= 1x10^–12(dBm)SOMA-
-8.68
Equivalent receiver sensitivity (OTU4 with Tx ER of 4 to 6.5 dB)(dBm)SAVG

-8.49
Equivalent receiver sensitivity (OTU4 with Tx ER > 7 dB)


-10.39
Stressed Receiver Sensitivity in OMA for Each Lane(100GbE)(dBm)


-6.810&11
Los Assert(dBm)
-25
-13.6
Los De-assert(dBm)


-11.3
Los Hysteresis(dBm)
0.5


Notes:

1.The supply current includes CFP2 module’s supply current and test board working current.

2.Average launch power, each lane (min) is informative and not the principal indicator of signal strength. A transmitter with launch power below this value cannot be compliant; however, a value above this does not ensure compliance

3.Even if the TDP<1dB, the OMA (min) must exceed this value

4.Transmitter reflectance is defined looking into the transmitter

5.The receiver shall be able to tolerate, without damage, continuous exposure to an optical input signal having this average power level

6.Minimum average receive power and maximum receiver sensitivity (OMA), each lane, is informative for 100GBase-LR4

7.Average receive power, each lane (min) is informative and not the principal indicator of signal strength. A received power below this value cannot be compliant; however, a value above this does not ensure compliance

8.Receiver sensitivity (OMA), each lane (max) is informative

9.Measured with PRBS 231-1 for BER=10-5. The BER for the OTU4 application is required to be met only after FEC has been applied.

10.Measured with conformance test signal at TP3 for BER=10-12

11.Conditions of stressed receiver sensitivity test: vertical eye closure penalty for each lane is 1.8dB; stressed eye J2 jitter for each lane is 0.3UI; stressed eye J9 jitter for each lane is 0.47UI.


Specification

No file

Recent browsing of products

Copyright © 2012-2016 Flyin Optronics Co.,Ltd. All Rights Reserved.